Arbitrary Waveforms Waveforms   The maximum arbitrary waveform size is 1 M points. Up to 500 user-defined waveforms may be stored on the removable memory card. Arbitrary waveforms can be defined by front panel editing controls, by downloading of waveform data via RS-232,USB or GPIB, or by writing directly to the removable memory card using the USB card reader/writer connected to a PC. Waveform memory   1 M points. Minimum waveform size is 8 points. Vertical resolution   12 bits Sample clock range   100 mHz to 80 MHz Resolution   4 digits Accuracy   ± 1 digit of setting Output filter   Selectable between 40 MHz Elliptic, 20 MHz Bessel or none Sequence   Up to 1024 waveforms may be linked. Each waveform can have a loop count of up to 32,768. A sequence of waveforms can be looped up to 1,048,575 times or run continuously. Noise function   Digital noise generated by a 35-bit linear feedback register clocked at 100 MHz. User’s external filter defines bandwidth and response Standard Waveforms Waveforms   Sine, square, triangle, DC, positive ramp, negative ramp, sin(x)/x, pulse, pulse train, cosine, haversine and havercosine Sine, Cosine, Haversine, Havercosine Range   0.1 mHz to 40 MHz Resolution   0.1 mHz or 10 digits Accuracy   Better than 10 ppm for 1 year Temperature stability   Typically < 1 ppm/°C Output level   5 mV to 20 V p-p from 50 Ω Harmonic distortion   < 0.15 % THD to 100 kHz; < –60 dBc to 20 kHz, < –50 dBc to 1 MHz, < –40 dBc to 10 MHz, < –30 dBc to 40 MHz Non-harmonic spurii   < –60 dBc to 1 MHz, < –60 dBc + 6 dB/octave 1 MHz to 40 MHz Square Range   1 mHz to 50 MHz Resolution   1 mHz (4 digits) Accuracy   ± 1 digit of setting Output level   5 mV to 20 V p-p from 50 Ω Rise and fall times   < 8 ns Triangle Range   0.1 mHz to 500 kHz Resolution   0.1 mHz or 10 digits Accuracy   Better than 10 ppm for 1 year Output level   5 mV to 20 V p-p from 50 Ω, linearity error: < 0.1 % to 30 kHz Ramps and Sin(x)/x Range   0.1 mHz to 500 kHz Resolution   0.1 mHz or 10 digits Accuracy   Better than 10 ppm for 1 year Output level   5 mV to 20 V p-p from 50 Ω Linearity error   < 0.1 % to 30 kHz Pulse and Pulse Train Output level   5 mV to 20 V p-p from 50 Ω Rise and fall times   < 8 ns Period   Range: 40 ns to 100 s; Resolution: 4-digits; Accuracy: ± 1 digit of setting Delay   Range: –99.9 s to + 99.99 s; Resolution: 0.001 % of period or 10 ns Width   Range: 10 ns to 99.99 s; Resolution: 0.001 % of period or 10 ns Trains of up to 10 pulses may be specified, each having independently defined width, delay and level. The baseline voltage is separately defined and the sequence repetition rate is set by the pulse train period. Operating Modes Continuous   Waveform runs continuously Triggered Burst Each active edge of the trigger signal will produce one burst of the waveform   Carrier waveforms   All standard and arbitrary Max. carrier frequency   The smaller of 2.5 MHz or the maximum for the selected waveform. 100 Msamples/s for ARB or Sequence. Number of Cycles   1 to 1048575 Trigger rep. rate   0.005 Hz to 100 kHz internal, dc to 1 MHz external Trigger source   Internal from keyboard or trigger generator. External from TRIG IN or remote interface. Start/stop phase   ± 360 ° settable with 0.1 ° resolution, subject to waveform frequency and type Gated Waveform will run while the Gate signal is true and stop while false   Carrier waveforms   All standard and arbitrary Max. carrier frequency   The smaller of 2.5 MHz or the maximum for the selected waveform. 80 Msamples/s for ARB or Sequence. Trigger rate   0.005 Hz to 100 kHz internal, dc to 1 MHz external Gate signal source   Internal from keyboard or trigger generator. External from TRIG IN or remote interface. Start/stop phase   ± 360 ° settable with 0.1 ° resolution, subject to waveform frequency and type Sweep Capability provided for both standard and arbitrary waveforms. Arbitrary waveforms are expanded or condensed to exactly 4096 points and DDS techniques are used to perform the sweep.   Carrier waveforms   All standard and arbitrary except pulse, pulse train and sequence. Sweep mode: Linear or logarithmic, continuous or triggered. Sweep direction   Up, down, up/down or down/up Sweep range   1 mHz to 40 MHz in one range. Phase continuous. Independent setting of start/stop frequency. Sweep time   1 ms to 999 s (3 digit resolution) Marker   Variable during sweep. Sweep trig. Source   The sweep may be free run or triggered from the following sources: Manually from keyboard. Externally from TRIG IN input or remote interface. Sweep hold   Sweep can be held and restarted by HOLD key Tone Switching Capability provided for both standard and arbitrary waveforms. Arbitrary waveforms are expanded or condensed to exactly 4096 points and DDS techniques used to allow instantaneous frequency switching.   Carrier waveforms   All waveforms bar pulse, pulse train, sequence Frequency list   Up to 16 frequencies from 1 mHz to 40 MHz Trigger rep. rate   0.005 Hz to 100 kHz internal, dc to 1 MHz external. Usable repetition rate and waveform frequency depend on the tone switching mode. Source   Internal from keyboard or trigger generator. External from TRIG IN or remote interface. Tone switching modes Gated   The tone is output while the trigger signal is true and stopped, at the end of the current waveform cycle, while the trigger signal is false. The next tone is output when the trigger signal is true again. Triggered   The tone is output when the trigger signal goes true and the next tone is output, at the end of the current waveform cycle, when the trigger signal goes true again. FSK   The tone is output when the trigger signal goes true and the next tone is output, immediately, when the trigger signal goes true again. External Amplitude Modulation Carrier frequency   Entire range for selected waveform Carrier waveforms   All standard and arbitrary waveforms Modulation source   Modulation socket Frequency range   DC to 500 kHz Signal range   Approx. 1 V pk-pk for 100 % level change at maximum output External Signal Summing Carrier frequency   Entire range for selected waveform Carrier waveforms   All standard and arbitrary waveforms Sum source   Sum socket Frequency range   DC to 16 MHz Signal range   Approximately 2 Vpk-pk input for 20 Vpk-pk output. Trigger Generator Source   Internal source 0.005 Hz to 100 kHz squarewave adjustable in 10 us steps. 3 digit resolution. Available for external use from the SYNC OUT socket. Main Outputs – One for each channel Output impedance   50 Ω Amplitude   5 mV to 20 V pk-pk open circuit (2.5 mV to 10 V pk-pk into 50 Ω. Amplitude can be specified open circuit (Hi Z) or into an assumed load of 50 Ωor 60 Ω, in Vpk-pk, Vrms or dBm. Ampl. accuracy   Better than 2 % ± 1 mV at 1 kHz into 50 Ω. Ampl. flatness   ± 0.2 dB to 1 MHz; ± 0.4 dB to 40 MHz DC offset range   ± 10 V. DC offset plus signal peak limited to ± 10 V from 50 Ω. Offset accuracy   Typically within ± 3 % ± 10 mV, unattenuated Resolution   3 digits or 1 mV for both Amplitude and DC Offset Sync Out – One for each channel Multifunction output user definable or automatically selected to be any of the following:   Waveform sync (All waveforms)   A square wave with 50 % duty cycle at the main waveform frequency, or a pulse coincident with the first few points of an arbitrary waveform. Position markers (Arbitrary only)   Any point(s) on the waveform may have associated marker bit(s) set high or low Burst done   Produces a pulse coincident with the last cycle of a burst Sequence sync   Produces a pulse coincident with the end of a waveform sequence Trigger   Selects the current trigger signal. Useful for synchronising burst or gated signals. Sweep sync   Outputs a pulse at the start of sweep to synchronise an oscilloscope or recorder. Can additionally output a sweep marker. Phase lock out   Used to phase lock two generators. Produces a positive edge at the 0o phase point. Output signal level   Logic level of < 0.8 V to > 3 V for all outputs except Sweep Sync. Sweep Sync is a 3-level waveform. Trig In Frequency range   DC to 1 MHz Signal range   Threshold nominally TTL level; max. input ± 10 V Min. rulse width   50 ns for Trigger and Gate modes; 50 µs for Sweep mode Input impedance   10 kΩ Modulation In Frequency range   DC to 500 kHz Signal range   VCA: Approximately 1 Vpk-pk for 100 % level change at maximum output   SCM: Approximately ± 1 Vpk for maximum output Input impedance   Typically 1 kΩ Sum In Frequency range   DC to 30 MHz (291) DC to 16 MHz (292/294) Signal range   Approximately 2 Vpk-pk input for 20 Vpk-pk output Input impedance   Typically 1 kΩ Hold   Holds an arbitrary waveform at its current position. A TTL low level or switch closure causes the waveform to stop at the current position and wait until a TTL high level or switch opening which allows the waveform to continue. The front panel MAN/HOLD key or remote command may also be used to control the Hold function. Input impedance   10 kΩ Ref Clock In/Out Set to input   Input for an external 10 MHz reference clock. TTL/CMOS threshold level. Set to output   Buffered version of the internal 10 MHz clock. Output levels nominally 1 V and 4 V from 50 Ω. Set to phase lock   Used together with SYNC OUT on a master and the TRIG IN on a slave to synchronize (phase lock) two generators ARB Clock In Frequency Range   DC to 50 MHz Max. input voltage   + 5 V, -1 V Inter-Channel Operation Inter-Channel Modulation The waveform from any channel may be used to Amplitude Modulate (AM) or Suppressed Carrier Modulate (SCM) the next channel. Alternatively any number of channels may be Modulated (AM or SCM) with the signal at the MODULATION input socket.   Carrier frequency   Entire range for selected waveform Carrier waveforms   All standard and arbitrary waveforms Modulation types   AM: Double sideband with carrier   SCM: Double sideband suppressed carrier Modulation source   Internal from the previous channel. External from Modulation input socket. The external modulation signal may be applied to any number of channels simultaneously Frequency range   DC to > 100 kHz Internal AM depth   0 % to 105 % Internal AM resolution   1 % Carrier Suppression (SCM)   > 40 dB External modulation signal range   VCA: Approximately 1 V pk-pk for 100 % level change at maximum output   SCM: Approximately ± 1 Vpk for max. output Inter-Channel Analogue Summing Waveform Summing sums the waveform from any channel into the next channel. Alternatively any number of channels may be summed with the signal at the SUM input socket.   Carrier frequency   Entire range for selected waveform Carrier waveforms   All standard and arbitrary waveforms Sum source   Internal from the previous channel. External from SUM IN socket. Frequency range   DC to > 16 MHz Ext. signal range   Approx. 5 Vpk-pk input for 20 Vpk-pk output Inter-Channel Phase Locking Two or more channels may be phase locked together. Each locked channel may be assigned a phase angle relative to the other locked channels. Arbitrary waveforms and waveform sequences may be phase locked but certain constraints apply to waveform lengths and clock frequency ratios.   With one channel assigned as the Master and other channels as Slaves a frequency change on the master will be repeated on each slave thus allowing multiphase waveforms at the same frequency to be easily generated. DDS waveforms are those with 7 digits of frequency setting resolution, while Non-DDS waveforms have 4 digits.   Phase resolution   DDS waveforms: 0.1 degree Non-DDS waveforms   0.1 degree or 360 degrees/number of points whichever is the greater Phase error   < ± 10 ns all waveforms. Inter-Channel Triggering Any channel can be triggered by the previous or next channel. The previous/next connections can be used to ‘daisy chain’ a trigger signal from a ‘start’ channel, through a number of channels in the ‘chain’ to an ‘end’ channel.   Each channel receives the trigger out signal from the previous (or next) channel, and drives its selected trigger out to the next (or previous) channel. The ‘end’ channel trigger out can be set up to drive the ‘start’ channel, closing the loop.   In this way, complex and versatile interchannel trigger schemes may be set up. Each channel can have its trigger out and its output waveform set up independently. Trigger out may be selected from Waveform End, Position Markers, Sequence Sync or Burst Done.   Using the scheme above it is possible to create a sequence of up to 64 waveform segments, each channel producing up to 16 segments and all channels being summed to produce the complete waveform at the output of channel 4.   The signals from the REF IN/OUT socket and the SYNC OUT socket can be used to phase lock two instruments where more than 4 channels are required.   Interfaces RS-232   Variable Baud rate, 9600 Baud maximum IEEE488   Conforms with IEEE488.2 USB   Conforms with USB 1.1 General Specifications Display   20 character x 4 row alphanumeric LCD Data entry   Keyboard selection of mode, waveform etc.; value entry by numeric keys or by rotary control. Memory card   Removable memory card conforming to the Compact Flash memory card standard. Sizes from 32 MB to 1 GB can be used. Stored settings   Up to 500 complete instrument set-ups may be stored and recalled from the memory card. Up to 500 arbitrary waveforms can also be stored independent of the instrument settings. Size   130 mm (3U) high; 335 mm long; 350 mm wide (292/294), 212 mm wide (291) Weight   292/294: 7.2 kg (16 lb); 291: 4.1 kg (9 lb) Power   110 to 120 V or 100 V nominal 50/60/400 Hz; 220 to 240 V nominal, 50/60 Hz. Voltage adjustable internally; operating range ± 10 % of nominal; 60 VA max. Installation Category II. Compliance Operating range   +5 °C to 40 °C, 20 to 80 % RH Storage range   –20 °C to +60 °C Environmental   Indoor use at altitudes to 200 m, Pollution Degree 2 Safety   Complies with EN61010-1 EMC   Complies with EN61326 Instrument drivers   Labview and LabWindows CVI drivers are either supplied with the instrument or are available via your local Fluke Office Supplied Items   IEC Mains Lead. Printed manual (partly multi-language), multi-language manual on CD, Waveform Manager Plus software, compact Flash memory card, compact Flash card reader/writer (USB connection to PC) Options   19-inch rack mounting kit

고액결제의 경우 안전을 위해 카드사에서 확인전화를 드릴 수도 있습니다. 확인과정에서 도난 카드의 사용이나 타인 명의의 주문등 정상적인 주문이 아니라고 판단될 경우 임의로 주문을 보류 또는 취소할 수 있습니다.  

무통장 입금은 상품 구매 대금은 PC뱅킹, 인터넷뱅킹, 텔레뱅킹 혹은 가까운 은행에서 직접 입금하시면 됩니다.  
주문시 입력한 입금자명과 실제입금자의 성명이 반드시 일치하여야 하며, 7일 이내로 입금을 하셔야 하며 입금되지 않은 주문은 자동취소 됩니다.

• 배송 방법 : 택배
• 배송 지역 : 전국지역
• 배송 비용 : 무료
• 배송 기간 : 3일 ~ 7일
• 배송 안내 : - 산간벽지나 도서지방은 별도의 추가금액을 지불하셔야 하는 경우가 있습니다.
  고객님께서 주문하신 상품은 입금 확인후 배송해 드립니다. 다만, 상품종류에 따라서 상품의 배송이 다소 지연될 수 있습니다.
  

교환 및 반품이 가능한 경우
- 상품을 공급 받으신 날로부터 7일이내 단, 가전제품의
  경우 포장을 개봉하였거나 포장이 훼손되어 상품가치가 상실된 경우에는 교환/반품이 불가능합니다.
- 공급받으신 상품 및 용역의 내용이 표시.광고 내용과
  다르거나 다르게 이행된 경우에는 공급받은 날로부터 3월이내, 그사실을 알게 된 날로부터 30일이내

교환 및 반품이 불가능한 경우
- 고객님의 책임 있는 사유로 상품등이 멸실 또는 훼손된 경우. 단, 상품의 내용을 확인하기 위하여
  포장 등을 훼손한 경우는 제외
- 포장을 개봉하였거나 포장이 훼손되어 상품가치가 상실된 경우
  (예 : 가전제품, 식품, 음반 등, 단 액정화면이 부착된 노트북, LCD모니터, 디지털 카메라 등의 불량화소에
  따른 반품/교환은 제조사 기준에 따릅니다.)
- 고객님의 사용 또는 일부 소비에 의하여 상품의 가치가 현저히 감소한 경우 단, 화장품등의 경우 시용제품을
  제공한 경우에 한 합니다.
- 시간의 경과에 의하여 재판매가 곤란할 정도로 상품등의 가치가 현저히 감소한 경우
- 복제가 가능한 상품등의 포장을 훼손한 경우
  (자세한 내용은 고객만족센터 1:1 E-MAIL상담을 이용해 주시기 바랍니다.)

※ 고객님의 마음이 바뀌어 교환, 반품을 하실 경우 상품반송 비용은 고객님께서 부담하셔야 합니다.
  (색상 교환, 사이즈 교환 등 포함)

상품의 사용후기를 적어주세요.

게시물이 없습니다

상품에 대해 궁금한 점을 해결해 드립니다.

게시물이 없습니다